扒渣机 耙斗机 电耙子 四不像 四不像矿车 专业制造

Sand scraper | slag scraper | sand scraper | sand climber | rock loader is the main equipment of early mine tunnel loading. It can replace manual loading operation in underground mine. The whole set is made up of machinery. As long as there is no shortage of gear oil in gearbox and drum and the gear oil is replaced on time, there will be no bad gear in all loading. Rock gear is occupied by fire, durable and durable. The premise of picking and loading machine working in underground is that the underground roadway needs to have installation track, slope less than 30 degrees, non-high gas coal mine. Our company produces and sells pickpockets and rock loaders. The whole plate is made of thick steel plate mixed with wear-resistant manganese steel, so it is suitable for back and forth friction in long-term rake bucket.

P-15耙斗机 扒装机 装岩机

Model P15 rake loader is suitable for use in tunnels of 2 m *2 m in size. Eleven KW explosion-proof motor is selected for P15 rake loader motor. Theoretically, the load per hour is 15-25 cubic meters, the volume of a rake is 0.15 cubic meters, the traction force of the main drum is 7.2-10.4 KN, and the standard wheel spacing is 600 mm. The main drum is suitable for steel wire rope 12.5, and vice drum can use 9 steel ropes. The size of the whole machine is about 4720 x 1150 x 1600. The main part of rock loader of picking and loading machine is driven by planetary wheel. The series of rake bucket machines have the characteristics of high rock loading efficiency, simple structure, good reliability, easy operation and wide application range. The rake bucket machine can not only be used in roadways, but also in inclined roadways below 30 degrees. It is to improve the speed of excavation and realize mechanization of roadway excavation. A major mechanical device.

P15耙斗机 扒装机 扒沙机在工地上的使用照片

P30耙斗装岩机 扒装机 装岩机

P30 loader is suitable for use in tunnels of 2.5 m 2.5 m or above. The explosion-proof motor of P30 rake bucket machine is 17KW. In theory, the load per hour is 35-50 cubic meters, the volume of a rake bucket is 0.3 cubic meters, the traction force of the main drum is 13.5-19.5 KN, and the standard wheel spacing is 600 mm. The main drum is suitable for the wire rope 12.5~15.5, and the auxiliary drum can use 9 steel ropes. The size of the whole machine is about 6600 x 1305 x 2000..

About maintenance of rock loader in skid loader:

1、电工接线后，应注意滚筒的转动方向，工作时从减速器一侧看，滚筒应为逆时针旋转，当同一时间两滚筒旋转的方向相反，则应以正在工作的一个为准。

1. After electrical wiring, attention should be paid to the direction of rotation of the drum. When working from the side of the reducer, the drum should rotate counterclockwise. When the direction of rotation of the two drums is opposite at the same time, the one that is working should prevail.

2、经常注意制动闸带及辅助刹车带的松紧程度是否合适，绞车转动是否灵活，工作是否可靠，如发现内齿轮抱不住或脱不开时，应调节闸带的调节螺栓使之合适。

2. Always pay attention to whether the tightness of brake band and auxiliary brake band is appropriate, whether the winch rotates flexibly and whether the work is reliable. If it is found that the inner gear can not be held or taken off, the adjusting bolt of brake band should be adjusted to make it suitable.

3、经常检查钢丝绳磨损情况，钢丝绳断裂时应及时更换。

3. Check the wear condition of wire rope regularly. Replace the wire rope when it breaks.

4、每月对各绳轮轴承加注黄油一次，每三个月对绞车减速器加90~150号工业齿轮油一次，每一个月对行星齿轮转动部分加90~150号工业齿轮油一次。

4. Butter is added once a month to the rope wheel bearings, 90-150 industrial gear oil is added to the winch reducer every three months, and 90-150 industrial gear oil is added to the planetary gear rotating part every month.

5、行星传动部分加油时，应注意勿使油落到滚筒制动面及闸带上，如发现上述部位有油迹应揩擦干净。

5. When refueling the planetary transmission part, attention should be paid not to make the oil fall on the brake surface and brake belt of the drum. If oil stains are found in the above parts, they should be wiped clean.

6、在平巷使用时，每天应检查风动系统油雾器的油位，如发现油位不足，应及时添加润滑油。

6. When using in roadway, the oil level of oil mist in pneumatic system should be checked every day. If it is found that the oil level is insufficient, the lubricant should be added in time.

7、经常注意钢丝绳接头是否牢固可靠，防止拉脱。

7. Always pay attention to whether the wire rope joint is reliable and reliable.

8、每星期检查一次各连接螺栓有无松动及失落，对松动件予以拧紧，并补上遗失件。

8. Check every week whether the connecting bolts are loose or lost, tighten the loose parts and fill in the missing ones.

9、每星期清理一次机器，将漏矸、岩渣及泥浆清理干净。

9, clean up the machine once a week, clean up the gangue, slag and mud.